Pelagic reservoir engineering

✨

From tkwa.me

Pelagic

Partner engineering2039 edition

Pelagic reservoir engineering is the material and thermal reference for designers making clothing and equipment for Pelagic Somatics subscribers. A garment can change its fit as a body changes, acquire a protective layer for an outing, or exchange material with a tool. Each operation draws on the same inventory used by Span to extend an arm to five metres. Designers specify the material transferred, the time available and where the resulting heat goes.

The reservoir travels beside its user on three fine legs and raises itself to the shoulder before an anticipated reach. Its flexible storage envelope contracts as material enters the arm and expands when material returns. Pumps, processors and support structure occupy a permanent core. The dock carries sealed supply and return channels; the feet carry the reservoir’s weight.

Material inventory#

Fuel and construction feedstock share a supply of reduced carbon. The reservoir meters this into a power converter or into the atomically precise manufacturing system that prepares tissue precursors and equipment materials. Finished biological feedstock reaches the body through a separately conditioned channel. Water, nitrogen-bearing compounds and mineral concentrates occupy other internal compartments. Hydrocarbons supply carbon and hydrogen; proteins also require nitrogen, and living tissue requires phosphorus, sulfur, salts and trace elements.

The ordinary power system takes oxygen from air. An oxygen-limited accessory can carry an isolated oxidizer cartridge, with its mass included in the accessory’s budget. Peroxide belongs in that separate circuit: storing an oxidizer beside a fuel requires controlled separation and metering. Stabilization changes its storage behaviour while leaving its oxidizing role intact.[1]

Body changes and recovery#

Trim subscribers with Span can use the larger reservoir for body transformations beyond the inventory carried by the grooming implant. A useful sizing example is 1 kg of wet tissue containing 750 g of water, 200 g of protein and 50 g of other constituents. At the conventional protein nitrogen fraction of 16%, its protein contains 32 g of nitrogen. The allocation is a reference composition; the selected tissue determines the actual inventory.[2]

Those 32 g of nitrogen are present in about 36 litres of ambient air. Collection is followed by chemical fixation, which consumes reducing power and requires catalysts. The reservoir carries bound nitrogen for rapid transformations and replenishes it between uses. In 2022, an experimental catalyst system demonstrated nitrogen fixation under ambient conditions using visible light and a chemical reductant.[3]

Stored water carries the much larger mass demand. Producing the example’s 750 g of water by oxidizing the reference hydrocarbon would consume about 0.58 kg of fuel and release 25 MJ of chemical energy, part of which could be converted to useful work. Returning water and useful molecules to the reservoir makes repeated transformations economical. Carbon already discharged as carbon dioxide needs new energy to become reduced-carbon feedstock again.

Bit, the hand-tool implant, ordinarily retains displaced tissue in the forearms. The external inventory supports larger equipment and provides somewhere to return its material. Recovery preserves usable molecules where practical, then sorts and reprocesses the remainder. The reservoir’s visible change in volume follows the quantities and densities transferred; its hardware retains its volume throughout a reach.

Power, air and heat#

The reference fuel has a lower heating value of 43 MJ/kg and an average hydrocarbon composition represented by CH2. The reaction balance is CH2 + 1.5 O2 → CO2 + H2O. This average unit makes the oxygen and water accounting reproducible. The converter combines fuel preparation with a fuel cell; the stated net efficiency includes the converter’s own auxiliary loads. Early fuel cells established the combination of efficient electrochemical conversion and few moving parts.[4][5]

Reference fuel-cell balance at 60% efficiency A chemical input of 166.7 watts divides into 100 watts of useful electrical output and 66.7 watts of conversion heat. Bar lengths show the energy proportions. This fixed example has no cooling load. Chemical input · 166.7 W Fuel cell · 60% electrical efficiency Electrical output 100 W · 60% Conversion heat 66.7 W · 40%
A 100 W electrical load at 60% efficiency consumes 166.7 W of chemical energy and releases 66.7 W at the fuel cell. Electrical work can subsequently become heat in the equipment it powers. This reference balance remains fixed while the calculator below explores other loads.

Reservoir load calculator#

Enter the equipment’s electrical demand and the heat to remove from its wearer. The cooling system draws additional electricity from the reservoir.

Operating point
0–1,000 W, before cooling power.
40–80% of fuel energy becomes electricity.
0–500 W of cooling.
1–6 W of heat moved per watt of electricity.

Calculated demand and heat balance
Cooling electricity0.0 W
Total electrical output100.0 W
Chemical power consumed166.7 W
Fuel consumption14.0 g/hour
Air at twice the reaction minimumAmbient air at 25°C and 1 atmosphere.5.8 L/min
Air at three times the reaction minimum8.7 L/min
Fuel-cell conversion heat66.7 W
Heat at the reservoir’s cooling surfaceWearer’s cooling load + cooling electricity + fuel-cell heat.66.7 W
Equipment output delivered at its point of use100.0 W
Total if all equipment power also becomes local heat166.7 W
Water evaporation for the cooling surfaceIdeal rate if evaporation carries the entire cooling-surface load.0.099 L/hour

Reference hydrocarbon feedstock: mean CH2 units, 43 MJ/kg lower heating value; each mole of CH2 consumes 1.5 mol O2. Air contains 20.95% O2. Water removes 2.4298 MJ/kg on evaporation; the volume estimate uses 1 kg/L. Net conversion efficiency includes converter auxiliaries; cooling performance includes the complete cooler. Both are selected design assumptions. The lower heating value assumes product water leaves as vapour. Humidity, transfer area and component losses enter the equipment specification.

Quiet air collection#

At 100 W electrical output and 60% conversion efficiency, fuel use is 14.0 g/hour. The oxygen reaction minimum corresponds to 2.9 L/min of air. Supplying two to three times that amount gives 5.8–8.7 L/min, allowing oxygen to remain in the exhaust. At the upper value, 200 cm² of open intake area gives a mean intake velocity of only 0.007 m/s. Broad porous intakes and low pressure-drop passages make unobtrusive collection plausible; fan speed, filters, valves and pressure losses determine the sound actually produced.

Oxygen can react at an air-fed electrode, so a separate oxygen concentrator is unnecessary for this operating mode. A dedicated separator has an additional work requirement. For ideal gases at the reference temperature, the reversible incremental extraction work is RT ln(1/y) per mole, with y the gas’s fraction in air. This gives about 34 Wh/kg for oxygen and 6.1 Wh/kg for nitrogen in the limit of very low recovery, with product delivered at ambient pressure. Finite recovery, compression and chemical fixation add their own demands.[6]

Cooling airflow can be much larger than reaction airflow. Removing the reference converter’s 66.7 W of heat using air warmed by 15°C takes about 224 L/min. The carrier spreads heat through its outer surface, available garment area and evaporative panels. A small fuel intake therefore says little by itself about the cooling system’s noise.

Extended comfort#

Temper moves up to 100 W of heat in its standalone configuration. Reservoir-connected comfort equipment adds heat exchangers and cooling capacity outside the implant. For an added 200 W cooling load and a coefficient of performance of 3 for the complete cooling system, the pump takes 66.7 W of electricity. At 60% conversion efficiency, its power supply adds 44.4 W of heat, giving a total of 311 W to reject at the carrier. This example exports no other electrical power.

Evaporating water at 30°C carries about 2.43 MJ/kg. Carrying all of that 311 W load by evaporation would use approximately 0.46 litres/hour. The converter produces only 12 g/hour of water. The lower-heating-value calculation lets that water leave as vapour; condensing it for reuse adds heat to the cooling load. Consequently, a comfortable afternoon needs stored water, a refill or another heat sink. Humidity and the vapour-pressure difference set the usable evaporation rate. Dry heat exchange works where surface temperature and airflow permit it; hot, humid conditions require more area or less cooling.[7]

Clothing and flight equipment#

Lifestyle and fashion licensees supply designs for fit, texture, drape, colour and appearance. Pelagic supplies fabrication, the material interface and adaptation to the wearer’s current body. Design profiles specify which parts can be resized, the material needed for a transformation, and the permitted loads and heat fluxes. A garment can keep its purchased design through a Trim transformation while drawing additional fabric from the reservoir. Mineral pigments, metal fittings and specialised protective materials require matching stock.

Sporting equipment also needs time and capacity reserved for fabrication. A product profile states its peak material flow and electrical load alongside its sustained use. Somatic clinics install the implants and establish the wearer’s interface positions. Designers leave contact surfaces, vents and the shoulder interface accessible in each supported body shape. Under handmade certification, a Bit-assisted maker can still place every part personally; the design licence and the method of assembly describe different aspects of the finished item.

Skim integration#

Skim uses the reservoir’s hydrocarbon supply for electrical conversion and propulsion, while separate construction stock forms its flight hardware. Before departure, the carrier stows its legs and locks into the flight structure close to the combined centre of mass. Pelvic and torso mounts carry thrust loads. The subsonic canopy encloses the head with internal clearance and a continuous windshield; fitted arm openings serve slower flight. The smooth exterior bridges the wearer’s body contours, with a faired bulge retaining fuel and unused material.

Hover petals and airflow#

Transparent petals spread roughly three to four metres across for takeoff, hover and landing. Their open electroaerodynamic channels accelerate ions, which transfer momentum to neutral air. Fine ribs carry the resulting loads through the petal roots into the torso and pelvis. Distributed channel control balances the thrust around the centre of mass. The broad flow produces a substantial breeze. Clothing and equipment profiles leave the channels, electrical insulation and flow paths clear.[8]

Area determines the airflow needed to support the wearer. For a reference combined mass of 120 kg, hover thrust is 1.18 kN. In the ideal actuator-disc comparison, induced velocity is vi = √(T / 2ρA), wake power is T vi, and far-wake speed is 2vi. The table uses air density 1.225 kg/m³ and effective open area A. Central clearance, gaps and inactive edges enlarge the visible footprint. The ideal wake power is a lower bound; the electrical supply also covers ion production, electrode losses and conversion losses.[10]

Reference hover airflow for a 120 kg combined mass
Effective open areaIdeal wake powerFar-wake speed
4 m²12.9 kW21.9 m/s
6 m²10.5 kW17.9 m/s
8 m²9.1 kW15.5 m/s
10 m²8.2 kW13.9 m/s

A separate electrical example uses 8 m² of active area and 8 N of thrust per kilowatt at the EAD terminals. It requires 147 kW at the petals. With 90% voltage-conversion efficiency and the reference 60% fuel-conversion efficiency, the reservoir supplies 163 kW of electricity from 272 kW of chemical input. Approximately 263 kW becomes local heat. Uniformly mixing that heat into the ideal hover stream would raise its temperature by 3.45°C. Actual channels need continuous heat paths from their electrodes, converters and supports into that flow.

Early EAD development established the tradeoff between active area, pressure losses and electrical demand. A ten-stage experiment in 2024 reached 26 N/m². A preceding design study modeled higher-density vertical-flight systems using improved ion sources, low-drag electrodes and power electronics. Pelagic’s porous structures apply those design principles at larger scale. Strong transparent materials support the thin ribs and insulation; the air still sets the required momentum flux.[11][12]

Transition and fast flight#

Forward turbines accelerate the prone flyer while aerodynamic lift and vectored thrust progressively take the load. Sufficient petal area remains active throughout that handover. The petals then retract or return their material to the reservoir; descent reverses the sequence. Their recovered material can form the high-speed ramjet ducts and pressure shell. The remaining reservoir retains its fuel allocation. Flush windows belong to the sealed thermal and pressure enclosure, with cooling and insulation around their mounts.

Flight requires a separate power and thermal budget. Skim’s low-power reference uses an extended five-metre lifting shell at Mach 4.8 and about 43 km altitude. At a combined cruise mass of 100 kg, its allocated 185 N drag requires about 286 kW of useful thrust power. Ramjet fuel supplies about 453 kW; another 5 kW of chemical input supplies 3 kW of auxiliary electricity. Total fuel input is about 458 kW, or 0.64 kg/min at 43 MJ/kg. A minute covers about 93 km. Climb, acceleration, hovering and reserves have separate phase budgets.

The Skim engineering account describes the slender lifting shell, passive control of boundary-layer transition, finite-loss ramjet cycle and explicit inlet momentum subtraction. Its radiating exterior handles most aerodynamic heating; fuel cooling protects concentrated hot spots and takes heat from the insulated cabin. Surface condition, carried mass and inlet recovery set the low-power operating envelope. The fast leg produces aerodynamic noise and a sonic-boom footprint.[8][9]

See also#

References#

  1. US Agency for Toxic Substances and Disease Registry. Hydrogen peroxide: medical management guidelines.
  2. FAO/WHO/UNU (1985). Energy and protein requirements, section 7.
  3. Ashida, Y. et al. (2022). Catalytic nitrogen fixation using visible light energy. Nature Communications 13, 7263.
  4. Burger, J. L. and Bruno, T. J. (2012). Application of the advanced distillation curve method to the variability of jet fuels. Energy & Fuels 26, 3661–3671.
  5. US Department of Energy. Fuel cells.
  6. Massachusetts Institute of Technology (2012). Thermodynamics of separation.
  7. National Institute of Standards and Technology. Water saturation table, 30°C row.
  8. Pelagic Somatics (2039). Skim® flight and thermal-protection manual.
  9. NASA Glenn Research Center. Drag equation.
  10. Johnson, W. (2009). NDARC: NASA Design and Analysis of Rotorcraft. NASA/TP-2009-215402.
  11. Gómez-Vega, N. and Barrett, S. R. H. (2024). Order-of-magnitude improvement in electroaerodynamic thrust density with multistaged ducted thrusters. AIAA Journal 62(4), 1342–1353.
  12. Barrett, S. R. H., Brown, A. and Gómez-Vega, N. (2023). Silent, Solid-State Propulsion for Advanced Air Mobility Vehicles. NIAC Phase I final report.